Servo motors with integrated drive: B&R ACOPOSmotor 8LMA33 and 8DI330, Beckhoff AMI8100 and Bosch Rexroth IndraDrive Mi – how they differ and what to watch for when replacing

Files to download
A servo motor with an integrated drive has the inverter built into the motor housing, so the control cabinet holds mostly power supplies and a single cable runs to the machine. A comparison of B&R ACOPOSmotor, Beckhoff AMI8100 and Bosch Rexroth IndraDrive Mi, with tips on what to check when replacing one.
Servo motors with integrated drive: B&R ACOPOSmotor 8LMA33 and 8DI330, Beckhoff AMI8100 and Bosch Rexroth IndraDrive Mi – how they differ and what to watch for when replacing
A servo motor with integrated drive is a motor in whose housing, or directly on which, an inverter is located, so mainly power supplies remain in the control cabinet, and a single cable combining power and communication runs to the machine. Such drives are used in modular and distributed machines, where successive modules can be built and commissioned independently. If a B&R ACOPOSmotor, Beckhoff AMI8100 or Bosch Rexroth IndraDrive Mi is working on the machine, then in the event of a failure the question immediately arises of what exactly to replace and how to read the data from the nameplates.
A short overview of the three solutions and their differences
B&R ACOPOSmotor 8DI330 is an inverter integrated directly on the motor, and the version designation is ACOPOSmotor, size 3, length 3, rated speed 4500 rpm. The electronics are cooled by the motor, which means that the inverter temperature is also determined by the load on the motor itself, not solely by the surroundings. The manufacturer describes the ACOPOSmotor module as a unit combining a servo drive with optional safety technology, a motor, a built-in position sensor and an optional gearbox.
The connection to the drive system in ACOPOSmotor is a hybrid connector. In the wired variant, the safety functions STO and SS1 are available. The degree of protection of the 8DI330 is IP64, optionally IP65, so when replacing it you need to know in which version the existing unit was working.
Beckhoff AMI8100 is a servo motor with integrated drive intended for mounting directly on the machine. As an EtherCAT slave, it can be mounted directly on the machine, without a control cabinet. It operates at a voltage of up to 48 V DC, and the device status is indicated by integrated status LEDs, which are the first source of information when diagnosing. Two additional 24 V DC inputs/outputs are available for drive-related functions.
Bosch Rexroth IndraDrive Mi allows machine manufacturers to integrate all the electrical drive components directly in the machine, without drive cabinets. In the KMS02.1B-A018 data, the power input voltage is DC 540...750 V, and the control voltage is DC 30...42 V. The degree of protection is IP65, and the output current is 5.85 A. The manufacturer states that the drive at the motor can only work with Rexroth drive components, that is, inverters, converters and power supplies of this brand.
What to watch for when replacing
The differences between these solutions translate into several specific checkpoints that are worth going through before ordering parts and before dismantling.
- Reading the nameplates: the full type designation from the motor and electronics nameplates, the serial number, and the hardware and software version, if they are placed on the housing, should be copied down, and the nameplates and connectors should be photographed before anything is disconnected. The designations should not be decoded on your own, because a wrongly guessed character can mean a different option.
- Supply voltage: the AMI8100 operates at up to 48 V DC, and the KMS02 at a power input voltage of DC 540...750 V, so these are different voltage classes and they must not be treated as mutual replacements.
- Degree of protection: ACOPOSmotor 8DI330 has IP64 with an IP65 option, whereas the KMS02 has IP65, which matters where the drive is exposed to water and dust.
- Connection: in ACOPOSmotor it is a hybrid connector, and in the AMI8100 daisy-chain and star wiring is possible, so the layout of cables and connectors in the machine depends on the chosen topology.
- Safety functions: the wired variant of ACOPOSmotor offers STO and SS1, and the AMI8100 optionally TwinSAFE STO/SS1, so it must be established whether the existing unit had this option.
- Practical checks: inspection of the housing and seals, the condition of connectors and contacts, assessment of the LEDs, checking values with a calibrator or current source, a parameter backup from before the replacement, and documenting the origin of the part.
In the case of ACOPOSmotor, the drive, motor, position sensor and optional gearbox form a single unit, so which of these elements are replaced separately must be established for the specific unit. For the Rexroth KSM/KMS series, replacement consists of replacing the motor with electronics with a new motor of the same type, and this rule applies only to this series.
Data to prepare before ordering
Before any inquiry or purchase, a complete set of information about the existing unit should be collected: the full type designation from the nameplate, the serial number, the hardware version and firmware, and photos of the nameplate and of all connectors. In addition there is a description of the application, that is, the role of the axis in the machine, the type of load and the way of supply. Thanks to this, the part can be matched unambiguously, and possible differences in options, such as safety or degree of protection, come to light before installation. It is also worth noting which components work with the drive in the given installation, because in the case of Rexroth this has a direct bearing on the operation of the whole system.
General replacement steps
The order of work is similar regardless of the manufacturer and begins with a parameter backup, because after the new drive is installed the parameters will be needed to restore the axis operation. Next, the type of the installed interface option and its version should be established, the power disconnected and a wait observed for the DC link to discharge, and the motor secured against falling, because after unscrewing it depends only on the fitter's grip. After dismantling, the old motor with electronics is compared with the new one in terms of nameplates, followed by installation and connection, commissioning, checking the inputs and outputs and communication, and finally homing again.
For Rexroth KSM/KMS the material gives specific steps. After disconnecting the power, 30 minutes should be allowed for the capacitors of the DC circuit to discharge, which protects against electric shock when touching live parts. The MMC card is removed from the old device in slot X7, because it holds the configuration that has to be transferred. In the new device the SERCOS address is set, the parameter set is loaded and the position reference is established again, that is, the axis is homed. It must also be taken into account that the motor cooling down can take up to 140 minutes, so after work under load the dismantling should not start immediately, because the housing may still be hot.
Questions and answers
Is a photo of the nameplate alone enough for a replacement?
A photo is a good supplement, but it does not replace copying down the full type designation, serial number and version, because a photograph can be illegible due to dirt or light reflection. It is worth having both forms of documentation, together with photos of the connectors.
What should be checked after commissioning the new drive?
First of all the status LEDs and the state of communication, then the operation of the inputs and outputs and the correctness of the axis homing. In the case of the AMI8100 the integrated status LEDs help, and after replacing a Rexroth KSM/KMS it is necessary to establish the position reference again.
Enetiv works in industrial automation from two sides: we supply parts and we repair them. We have new, used and refurbished parts from brands including Allen-Bradley (Rockwell Automation), Siemens, Schneider Electric, Bosch Rexroth and ABB, we diagnose and repair inverters, servo drives, I/O modules and controllers, we service motors and servomotors, with our own warranty on repairs. We also specialize in end-of-life (EOL) parts and service, including older-generation and unusual components. Please contact us at https://enetiv.com/zapytanie.
Sources
- ACOPOSmotor – product family page - B&R
- ACOPOSmotor 8DI330.ff045hi00-1 – product data sheet - B&R
- Distributed drive systems (AMI8100) – product overview - Beckhoff
- Servo drives – product overview - Beckhoff
- IndraDrive Mi KMS02 Near Motor Servo Drive – data sheet - Bosch Rexroth
- IndraDrive Mi KSM – manual, document R911322511 - Bosch Rexroth
Publication date: 20.11.2026